AUTOMATIC TRANSFER SWITCH CONTROLLER

ATS Controller Training Video

USING OUR GUIDELINES YOU CAN MAKE COST-EFFECTIVE AUTOMATIC TRANSFER SWITCH PANELS

What is an Automatic Transfer Switch

  This accomplishes an automatic transfer switch of the LOAD in case of a power outage. The automatic transfer switch controller is the module that governs the Automatic Transfer Switch Panel.


USE THE BE242 TO CUT 50% OF THE COSTS


1) USE THE BE242 AUTOMATIC TRANSFER SWITCH CONTROLLER TO SAVE 20 METERS OF CABLE

OLD AMF PANEL WIRINGS

2) THE BE242 AUTOMATIC TRANSFER SWITCH CONTROLLER

NEEDS A ROUND CUT-OUT

NO MORE MECHANICAL WORK

3) MAKE A CIRCULAR 57mm (2 1/4") HOLE USING A SAW DRILL BIT CUTTER

4) THE BE242 AUTOMATIC TRANSFER SWITCH CONTROLLER DOES NOT NEED ADDITIONAL COMPONENTS

REDUCE COMPONENTS COUNT


We design the future generation of AUTOMATIC TRANSFER SWITCH CONTROLLERS. We take care to provide state-of-art solutions for our valuable customers. Firstly, the automatic transfer switch controller allows you to make advanced state-of-art Automatic Generator Panels saving connections, wires, components, and labor hours. Secondly, by installing the controller on the door front you are required to cut out a round area similar to panel instruments. Thirdly, the Be242 automatic transfer switch contains all electronic circuits in a compact 20mm thin enclosure.


INVEST IN YOURSELF

LEARN HOW TO MAKE AUTOMATIC TRANSFER SWITCH PANELS

PURCHASE THE

PDF E-BOOK

4.99€

PURCHASE VIA PAYPAL


An old-fashioned automatic transfer switch controller needs as many as 50 meters of cables and as many as 100 connections to the terminal blocks of the controller and to the terminal block of the panel not to mention relays and accessories. So, we introduced a new concept.  The Be242 Automatic Transfer Switch controller is made of two boards. As a result, you no longer need to place tens of cables up to the panel door. Finally, the user interfaces part of the automatic transfer switch controller is fitted on the front door of the panel. Additionally, on the panel backplane, you are required to install, on a suitable rail, the Be242RB relay board that interfaces with the generator, engine, and utility power via short wires.

THE SLIMMEST AUTOMATIC TRANSFER SWITCH  CONTROLLER OF THE WORLD

THE SLIMMEST ATS CONTROLLER IN THE WORLD

The automatic transfer switch controller reads voltages and currents of the Mains and generator via the interface board BE242RB.  You are no longer required to connect intermediary terminal blocks and wires.

AUTOMATIC TRANSFER SWITCH CONTROLLER INSTALLATION MANUAL

You will connect the generator & engine directly to the interface module. The internal board Be242RB (it stands for RELAY BOARD) directly interfaces with the generator and mains via short wires.

A visual perspective from the BE242 side.

You are no longer required to wire connections to the rear door panel. The BE242RB board includes auxiliary relays and short-circuit-proof components. To make a professional Automatic Transfer Switch panel, you only require a metal or plastic cabinet, battery charger, current transformers, and contactors. By using the configurable INPUT-OUTPUT options you can choose the best solution for you.

AUTOMATIC TRANSFER SWITCH CONTROLLER PRICE

(KIT CONTROLLER+RELAY BOARD)

 299€

FREE SHIPPING WORLDWIDE

SUPPORT (GMT+1) +40 721 241 361 
CONTACT US [email protected]


2 SET OFFER

(KIT CONTROLLER+RELAY BOARD)

 199€ / each

FREE SHIPPING EU US CANADA
LIFETIME WARRANTY

HOW TO WIRE AUTOMATIC TRANSFER SWITCH CONTROLLER

4 SET OFFER

(KIT CONTROLLER+RELAY BOARD)

 159€ / each

FREE SHIPPING TO EU-US-CANADA
LIFETIME WARRANTY

ASK FOR 10-25-50 BULK ORDER OFFER


Despite its square shape, the automatic transfer switch controller requires a round hole. You can make a round hole ranging from 56mm up to 70mm. We recommend that you make also 4 small holes required to get the IP62 ingress protection. This operation will take only 5 minutes of work. Forget about cutting a big square hole that requires special metal cutting tools. You can use a simple circular cutting drill. The following footprint will help you position the drill. It includes the optional hole suitable for EMERGENCY SWITCH.

 

BE242 REAR VIEW DESCRIPTION

SETTING UP THE AUTOMATIC TRANSFER SWITCH CONTROLLER

The automatic transfer switch controller features a user-friendly interface. The installation manual presents a clear alphabetic list of all settings. Consequently, the automatic transfer switch controller setup requires a few seconds only. As a matter of fact, the ATS controller is delivered ready for use especially if you have a 400V 3-phase system. In case of doubts, you can call our 24-7-365 support desk +39 335 70 77 148. In a matter of seconds, as an option, you can restore the factory settings. Normally you may need to set up the automatic transfer switch controller in particular applications or when you have to arrange special wiring. To summarize, the automatic transfer switch controller features over 100 parameters and settings. In conclusion, this will allow you extraordinary flexibility of use. You can arrange a dual-set configuration or dual-load configuration.

 

AUTOMATIC TRANSFER SWITCH CONTROLLER DIAGRAM PDF

Open a STEP-BY-STEP training video. Firstly, you will see the simplest way to build a generator control panel saving time and money. Basically, you will make all connections on a single back-plane. You will connect the back-plane to the ATS controller via a special cable supplied in the BE242 KIT. The system is flexible and adjustable.  In other words, you can directly connect an engine or other controllers like auto-start modules.

The BE242 automatic transfer switch controller accepts single or tri-phase ALTERNATING voltage connected to utility power and generator. As a result, you can handle mixed configurations single-phase or tri-phase for generator and utility power. Most importantly, the relay outputs are short-circuit-proof. Consequently, the BE242RB directly controls and drives the coils of the contactors via protection fuses. You can supply the Be242 automatic transfer switch controller up to 33VDC in a fully operating range of -25 up to +70 degrees Celsius. Additionally, the adjustable settings of the BE242 controller cover your protection settings up to a 2000kVA generator.

AUTOMATIC TRANSFER SWITCH CONTROLLER SPECIFICATIONS

DC Supply: 5.5/36Vdc, 50/150mA

Protection: 300mA thermal fuse

Dimensions:: 192 X 144 X 200 (mm)

Panel Cut-out: Round 56mm up to 70mm

Operating temperature: -25 deg C up to +70 deg C

Humidity range: 5% up to 95%

Weight: 230 grams

Meets ECC 89/336, 89/392, 73/23, 93/68, IEC 68-2-6

Certification: CE

Display: 4 digits red color

LED Indicators: 5 nos Yellow & 8 nos Green

Pushbuttons: 12 Membrane 100.000 actions life

Over  70 programmable adjustable settings

THE BE242RB RELAY BOARD INTERFACE

Supply Voltage: 5.5-36Vdc, 50-150mA

Protection: internal 4A thermal fuse

Dimensions: 200 X 140 X 70 (mm)

Installation: DIN-RAIL clips, IP62

Temperature: -25 deg C up to +70 deg C.

 Humidity: 5% up to 95%

Weight: 500 grams

Metts ECC 89/336, 89/392, 73/23, 93/68.

Certification: CE

DC Relay Outputs: 1A 30VDC.

AC Relay Outputs: 5A 250V  AC

Output Fuses: 3,15A Quick Action

Connectors: removable terminal blocks

Operating Vac: 500Vac

Overvoltage Voltage: 4KVac

CTs: 5Aac nominal, 8Aac 1 minutes

 

USER-FRIENDLY AUTOMATIC TRANSFER SWITCH CONTROLLER

KEEP-IT-SIMPLE is our master KEYWORD. We designed this ATS controller in a way to is intuitive and simple to use. Normally end-users have no knowledge about electrical items. For this reason, we put on the front panel only the necessary components. We use solid-state lamps and a simple 4-digit display. This ATS controller will last for over 25 years under continuous supply. The current for the lamp is chosen for the longest lifetime. In the following example, we show the basic conditions: LOAD connected to UTILITY POWER and LOAD connected to a STANDBY GENERATOR.

 

Load Connected To Mains

Directly push a button to select the MODE of operation. The LED indicator will immediately confirm the operation. To shut down the controller, push the OFF button. According to the setting of the PARAMETER NFPA-110, the BE242 automatic transfer switch controller will transfer the load to MAINS even if the MAINS is not within the settings. In the OFF mode of operation, you are allowed to program the controller.

 

Load Connected To Generator

In the MANUAL MODE of operation, you can start & stop the engine.  You can control the contactors or the transfer switch. When in AUTO MODE, the manual commands are disabled and the automatic transfer switch controller will perform all tasks based on your automation settings. If DC power fails, the ATS controller will restart all sequences. It uses a NON-VOLATILE area of the memory to store the tasks before DC power down. All adjustable parameters are stored redundantly if separated memories. In case of a high level of noise, or software crash,  the microcontroller will be able to recover in the correct way stored data.


 BERNINI DESIGN SRL

Zona Industriale,

46035 Ostiglia Italy

[email protected]

  24/7/365 support 0040 721241361

 

The be242 is a combined automatic mains failure automatic transfer switch and generator controller. We also recommend that you consider this product when you refurbish an old generator

Benefit Nr1

- You save 50% time in making a panel

- You make a round hole in the door

- All 400-volt connections are made in the backplane panel

- There is no ac cables connecting the front door

-  You save 20 meters of cables and no interference with low voltage circuits in case of lightning

- This means long-term reliability

- The Be242 directly interfaces with other controllers or directly with the engine via the Be242 relay board.

Benefit nr.2

- The Be242 is connected to the relay board via a special cable supplied with the kit.

- You no longer need fuses, relays and additional terminal blocks.

Benefit nr.3

- The product is designed to be user-friendly, and the user interface is simple

- All basic functions are clear to understand

- No complex menus, only powerful el li dis indicators

- The display is capable of working in a wide temperature range

Here you can see the load connected to utility power.

Here you can see the load connected to a generator.

Here you can see some of the messages indicated by the display.

Benefit nr4

- The front panel is 20mm thin and mechanically connected to the door via a full polypropylene gasket that guarantees if very well installed, a full IP65 ingress protection if you have a suitable cabinet.

- Being the controller installed on the external side of the door, the electromagnetic noise generated by the switchings of the power contactors or the breakers will not affect the controller's functionality in other words the front door is used as a powerful shield.

- The be242 can work in extreme conditions as well.

Benefit nr5

- Easy to program

- You can set up all adjustable parameters about utility power-generator-engine- alarms and so on.

- The Be242 is designed to continuously work for at least 25 years. For this reason, we provide unlimited warranty.

- Visit our website today to find out more about this extraordinary product.